Installing prelude fog light

Rear Step Bumper. Pillar Trim. Tow Trailer Hitch. Fuel Door. Car Cover. Tail Gate Protector. Truck Bed Side Rail. Rear Bumper Guard. Tool Box. Rail Cap. Chase Rack. Mud Guard. Light Bar Bracket. Window Louvers. Truck Bed Liner. Catback Exhaust.

Catalytic Converter. Down Pipe. Test Pipe. Turbo Manifold. Intake Manifold. Air Intake. Radiator Cooling Fan. Fuel Tank. Radiator Fan Shroud. Blow Off Valve. Intercooler Kit. Boost Controller. Braided Steel Hose. Oil Catch Tank. Cam Gear. Fuel Line. Fuel Pressure Regulator. Short Shifter. Radiator Hose. Fuel Power Torque Plate. Fuel Cell Tank. Engine Mount. AC Condenser. Coolant Recovery Tank. Lift Kit. Lowering Springs. Strut Bar. Harness Tie Bar. Sub-Frame Kit. Battery Tie Bar. Bump Steer Kit.

Shock Spacer. Sway Bar Drop Bracket. Adjustable Track Bar. Steering Wheel. Shift Knob. Rearview Mirrors. Seat Cover. Air Freshener. Disconnect the fog light switch from the housing.

It should disconnect by detaching the clip. Remove the washer, bolt, and nut. This will allow you to remove the fog light housing. Make sure that you hold on to all your parts until the installation is complete. Remove the housing. Be careful not to scratch the bumper. If you are installing grille or roof-mounted lights, lift away from the vehicle to be sure to avoid scratching the roof or body.

Insert the new fog light. The housing should fit into the space left by the old one. If it does not, you may have purchased the incorrect headlights. Make sure that the bolt holes line up; otherwise you may have to drill new ones. Insert the bolt. Thread the washer and nut over the bolt, tightening with a ratchet or wrench. Do not over tighten as you may damage the fog light housing or the vehicle.

The housing should be snug and immobile. Reattach the switch. Reconnect the fog light switch using the clip. Start the ignition. Test your new lights. Yes No. Not Helpful 8 Helpful Zipties and electrical conduit. Pay attention and don't let slack fall onto the radiator, fans, belts, or the engine itself. Not Helpful 0 Helpful 3. How do I install exterior accent lights on a Volkswagen Jetta where the fog lights go?

You'll need, a Dremel to cut out the holes on the front bumper to be able to mount the lights underneath, and extra wiring connections to tie the lights into your existing electrical system. As an added idea, consider adding an extra set on the bottom of the rear bumper to aid in backing up at night. Not Helpful 0 Helpful 1. Pull out the old one and take it to an auto parts store, they will know what to sell you. Make sure to replace in pairs, and tell them that they need to be street legal -- fog lights use special bulbs that are physically similar to, but can be made very powerful, and are designed for off-road use on vehicles like jeeps.

I bought a new set of Blazer headlights. Are brass rings attached by a wire on the bottom of both lights? I found this odd. But to get to my question: the lights fail to come on. The power switch lights up, but that's it.

Any idea why this is happening? The brass rings are probably intended to ground the lights. And if they aren't attached to a ground, that's probably why your lights won't work. Not Helpful 2 Helpful 3. Include your email address to get a message when this question is answered. By using this service, some information may be shared with YouTube. If you are replacing the bulb and not the housing, be sure to replace the bulb with the same type.

Helpful 0 Not Helpful 0. Be sure that the car is completely off before installing new lights. Helpful 15 Not Helpful Helpful 16 Not Helpful You Might Also Like How to. How to. Co-authors: Updated: April 8, Categories: Car Lighting. Italiano: Installare i Fari Fendinebbia.

Nederlands: Mistlampen monteren. Thanks to all authors for creating a page that has been read , times. Did this article help you? Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy.

About This Article. Featured Articles How to.